Полезная информация

cc/td/doc/product/software/ios120/12cgcr/ibm_c
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Configuring NCIA Client/Server Topologies

Configuring NCIA Client/Server Topologies

This chapter describes native client interface architecture (NCIA) support for Systems Network Architecture (SNA) devices. NCIA server and the NCIA client/server model extends the scalability of NCIA  I, the earlier NCIA implementation, by minimizing the number of central-site remote source-route bridging (RSRB) or data-link switching plus (DLSw+) peer connections required to support a large number of NCIA clients. For a complete description of the NCIA client/server commands mentioned in this chapter, refer to the "NCIA Server Configuration Commands" chapter of the Bridging and IBM Networking Command Reference. To locate documentation of other commands that appear in this chapter, use the command reference master index or search online.

Cisco's NCIA server feature implements RFC 2114, Data Link Switch Client Access Protocol.

NCIA Server Session to Local Token Ring Using DLSw+ Local Switch

The network configuration shown in includes NCIA clients that connect to a front-end processor (FEP) on a Token Ring through a local router (the NCIA server). The virtual ring is used in conjunction with DLSw+ local switch. The routing information field (RIF) of each circuit is terminated on the virtual ring. Figure 160 shows a logical view of an NCIA server session using a DLSw+ local switch (connected to a local Token Ring). In addition to Token Ring, an NCIA server also supports Ethernet, Synchronous Data Link Control (SDLC) Protocol, and Qualified Logical Link Control (QLLC) network connections as well as Channel Interface Processor (CIP) connections through a DLSw+ local switch. For more information on the different media types that a DLSw+ local switch supports, refer to the "Configuring DLSw+" chapter.


Figure 159: NCIA Server Session to Local Token Ring Using DLSw+ Local Switch



Figure 160:
Logical View of NCIA Server Session to a Local Token Ring Using DLSw+ Local Switch


Configuration Task List

To configure an NCIA server session connected to a local Token Ring, perform the tasks in the following sections:

For a configuration example, see "NCIA Server Session to Local Token Ring Using DLSw+ Local Switch Example" at the end of this chapter.

Define a Source-Bridge Ring Group for DLSw+

In DLSw+, the source-bridge ring group specifies the virtual ring that will appear to be the last ring in the RIF. This ring is transparent to the NCIA client. From the host's point of view, all NCIA clients look like stations sitting on the virtual ring. To define a source-bridge ring group for DLSw+, use the following command in global configuration mode:
Command Purpose

source-bridge ring-group ring-group [virtual-mac-address]

Define a ring group.

Define a DLSw+ Local Peer for the Router

Defining a DLSw+ local peer for a router enables DLSw+ local switch. You specify all local DLSw+ parameters as part of the local peer definition. To define a local peer, use the following command in global configuration mode:
Command Purpose

dlsw local-peer [peer-id ip-address] [group group] [border] [cost cost] [lf size] [keepalive seconds] [passive] [promiscuous] [biu-segment]

Define the DLSw+ local peer.

Configure an NCIA Server on the Router

Configuring an NCIA server on a router enables the router to perform two roles:

To configure an NCIA server, use the following command in global configuration mode:
Command Purpose

ncia server server-number server-ip-address server-virtual-mac-address virtual-mac-address virtual-mac-range [inbound-only] [keepalive seconds] [tcp_keepalive minutes]

Configure the NCIA server.

NCIA Server Session with DLSw+

In the network configuration shown in Figure 160, the NCIA server uses DLSw+ to connect its clients to the FEP through a remote router. Figure 162 shows a logical view of the NCIA Server session with DLSw+.


Figure 161:
NCIA Server Session with DLSw+



Figure 162:
Logical View of NCIA Server with DLSw+


DLSw+ Configuration Task List

To configure an NCIA server session connected to a remote router using DLSw+, perform the tasks in the following sections:

For a configuration example, see "NCIA Server Session with DLSw+ Example" at the end of this chapter.

Define a Source-Bridge Ring Group for DLSw+

The source-bridge ring can be shared between DLSw+ and SRB/RSRB. In DLSw+, the source-bridge ring group specifies the virtual ring that will appear to be the last ring in the RIF. Because RIFs are terminated at the router, there is no correlation between the ring-group number specified in DLSw+ peers. The numbers can be the same for management simplicity, but they do not have to be. To define a source-bridge ring group for DLSw+, use the following command in global configuration mode:
Command Purpose

source-bridge ring-group ring-group [virtual-mac-address]

Define a ring group.

Define a DLSw+ Local Peer for the Router

Defining a DLSw+ local peer for a router enables DLSw+. You specify all local DLSw+ parameters as part of the local peer definition. To define a local peer, use the following command in global configuration mode:
Command Purpose

dlsw local-peer [peer-id ip-address] [group group] [border] [cost cost] [lf size] [keepalive seconds] [passive] [promiscuous] [biu-segment]

Define the DLSw+ local peer.

Define a DLSw+ Remote Peer

To configure TCP encapsulation on a remote peer, use the following command in global configuration mode:  
Command Purpose

dlsw remote-peer list-number tcp ip-address [backup-peer ip-address] [bytes-netbios-out bytes-list-name] [cost cost] [dest-mac mac-address] [dmac-output-list  access-list-number] [dynamic] [host-netbios-out host-list-name] [inactivity minutes] [keepalive seconds] [lf size] [linger minutes] [lsap-output-list list] [no-llc minutes] [priority] [tcp-queue-max size] [timeout seconds]

Define a TCP encapsulation remote peer.

Configure an NCIA Server on the Local Router

Configuring an NCIA server on the local router enables the router to perform two roles:

To configure an NCIA server, use the following command in global configuration mode:
Command Purpose

ncia server server-number server-ip-address server-virtual-mac-address virtual-mac-address virtual-mac-range [inbound-only] [keepalive seconds] [tcp_keepalive minutes]

Configure the NCIA server.

NCIA Server Session with DSPU

In the network configuration shown in Figure 163, the NCIA server uses DSPU to connect its clients to the FEP through a remote router. Figure 164 shows a logical view of the NCIA server session with RSRB/DLSw+ and DSPU.


Figure 163:
NCIA Server Session with DSPU



Figure 164:
Logical View of NCIA Server with DSPU


DSPU Configuration Task List

To configure an NCIA server session connected to a remote router using DSPU, perform the tasks in the following sections:

For a configuration example, see "NCIA Server Session with DSPU Example" at the end of this chapter.

Define a DSPU Upstream Host

To define a DSPU host over Token Ring, Ethernet, Fiber Distributed Data Interface (FDDI), RSRB, or virtual data link control (VDLC) connections, use the following command in global configuration mode:
Command Purpose

dspu host host-name xid-snd xid rmac remote-mac [rsap remote-sap] [lsap local-sap] [interface slot/port] [window window-size] [maxiframe max-iframe] [retries retry-count] [retry-timeout retry-timeout] [focalpoint]

Define a DSPU host over Token Ring, Ethernet, FDDI, RSRB, or virtual data link control connections.

Explicitly Define DSPU

To explicitly define a DSPU over Token Ring, Ethernet, FDDI, RSRB, VDLC, or NCIA connections, use the following command in global configuration mode:
Command Purpose

dspu pu pu-name [rmac remote-mac] [rsap remote-sap] [lsap local-sap] [xid-rcv xid] [interface slot/port] [window window-size] [maxiframe max-iframe] [retries retry-count] [retry-timeout retry-timeout]

Explicitly define a DSPU over Token Ring, Ethernet, FDDI, RSRB, VDLC, or NCIA connections.

Define Dedicated LU

To define a dedicated logical unit (LU) or a range of dedicated LUs for an upstream host and DSPU, use the following command in global configuration mode:
Command Purpose

dspu lu lu-start [lu-end] {host host-name host-lu-start | pool pool-name} [pu pu-name]

Define a dedicated LU or a range of dedicated LUs for a DSPU.

Configure the NCIA Server as the Underlying Transport Mechanism

To configure the NCIA server as the underlying transport mechanism, use the following command in global configuration mode:
Command Purpose

dspu ncia [server-number]

Configure the NCIA server as the underlying transport mechanism.

To enable a local Service Access Point (SAP) on the NCIA server for use by DSPUs, use the following command in global configuration mode:
Command Purpose

dspu ncia enable-pu [lsap local-sap]

Enable local SAP for DSPUs.

NCIA Server Session with RSRB

The network configuration shown in Figure 164 includes NCIA clients that connect to a FEP on a Token Ring through a remote router. Figure 166 shows a logical view of the NCIA Server session with RSRB (to a remote Token Ring). Because DLSw+ is the latest technology provided by Cisco, Cisco does not encourage using the NCIA Server feature with RSRB. If the router on the host side is running DLSw+, RSRB should not be used. Support for the NCIA Server feature with RSRB is provided to encourage RSRB users to migrate to DLSw+.


Figure 165:
NCIA Server Session with RSRB



Figure 166:
Logical View of NCIA Server Session with RSRB (Remote Token Ring)


RSRB Configuration Task List

To configure an NCIA server session connected to a remote Token Ring using RSRB, perform the tasks in the following sections:

For a configuration example, see "NCIA Server Session with DLSw+ Example" at the end of this chapter.

Define a Source-Bridge Ring Group for DLSw+ and RSRB

The source-bridge virtual ring can be shared between DLSw+ and SRB/RSRB. In DLSw+, the source-bridge ring group specifies the virtual ring that will appear to be the last ring in the RIF. Because RIFs are terminated at the router, the ring group numbers specified in commands to set up DLSw+ peers can be different. The ring group numbers can be the same for management simplicity, but they do not have to be.

To define a source-bridge ring group for DLSw+, use the following command in global configuration mode:
Command Purpose

source-bridge ring-group ring-group [virtual-mac-address]

Define a ring group.

Identify the Remote Peer (TCP Connection)

In our implementation, whenever you connect Token Rings using non-Token Ring media, you must treat that non-Token Ring media as a virtual ring by assigning it to a ring group. Every router with which you want to exchange Token Ring traffic must be a member of this same ring group. For more information about defining a ring group, see the "Define a Ring Group in SRB Context" section of the "Configuring Source-Route Bridging" chapter of this document.

To identify the remote peers, use the following command in global configuration mode:
Command Purpose

source-bridge remote-peer ring-group tcp ip-address [lf size] [tcp-receive-window wsize] [local-ack] [priority]

Identify the IP address of a peer in the ring group with which to exchange source-bridge traffic using TCP.

Specify one source-bridge remote-peer command for each peer router that is part of the virtual ring. Also specify one source-bridge remote-peer command to identify the IP address of the local router.

NCIA server supports only RSRB pass-through mode. Local acknowledgment is not supported.

Define a DLSw+ Local Peer for the Local Router

Defining a DLSw+ local peer for the local router enables DLSw+. You specify all local DLSw+ parameters as part of the local peer definition. To define a local peer, use the following command in global configuration mode:
Command Purpose

dlsw local-peer [peer-id ip-address] [group group] [border] [cost cost] [lf size] [keepalive seconds] [passive] [promiscuous] [biu-segment]

Define the DLSw+ local peer.

Configure an NCIA Server on the Router

Configuring an NCIA server on a router enables the router to perform two roles:

To configure an NCIA server, use the following command in global configuration mode:
Command Purpose

ncia server server-number server-ip-address server-virtual-mac-address virtual-mac-address virtual-mac-range [inbound-only] [keepalive seconds] [tcp_keepalive minutes]

Configure the NCIA server.

Configure an RSRB Ring for the NCIA Server on the Local Router

Configuring an RSRB ring to associate with the NCIA server on the local router provides the virtual ring that connects the DLSw ring within the local router and the target ring between the local router and the remote router.

To configure an RSRB ring for the NCIA server on the local router, use the following command in global configuration mode:
Command Purpose

ncia rsrb virtual-ring local-bridge local-ring ncia-bridge ncia-ring virtual-mac-address

Define the NCIA/RSRB interface.

Monitor and Maintain an NCIA Server Network

You can monitor and maintain the operation of an NCIA server network. To display information about the state of the NCIA server feature and perform maintenance tasks, use the following commands in EXEC mode:
Command Purpose

show ncia server [server-number]

Show the status of the NCIA server.

show ncia client [sap-list] [ip-address]

Show the status of the NCIA client.

clear ncia client [ip-address]

Terminate an NCIA client connection.

show ncia circuits [id-number]

Show the status of an NCIA circuit.

clear ncia circuit [id-number]

Drop an NCIA circuit.

clear ncia client registered [ip-address]

Terminate the active connection to the specified client and release all control blocks of the registered client.

ncia stop

Stop an NCIA server.

ncia start

Restart an NCIA server.

NCIA Server Configuration Examples

The following sections provide NCIA server configuration examples:

NCIA Server Session to Local Token Ring Using DLSw+ Local Switch Example

Figure 166 illustrates the use of DLSw+ local peer with an NCIA server session to a local Token Ring.


Figure 167:
NCIA Server Session to Local Token Ring Using DLSw+ Local Switch


The following is a configuration file for the network example shown in Figure 166:

source-bridge ring-group 44
dlsw local-peer
ncia server 1 10.2.20.4 4000.3174.0001 4000.0000.0001 128
!
interface token ring 0
  ring-speed 16
  source-bridge 21 3 44

NCIA Server Session with DLSw+ Example

Figure 166 illustrates the use of DLSw+ with an NCIA server session.


Figure 168:
NCIA Server Session with DLSw+


The following is a configuration file for the network example shown in Figure 166:

source-bridge ring-group 44
dlsw local-peer peer-id 10.2.20.4
dlsw remote-peer 0 tcp 10.2.20.3
ncia server 1 10.2.20.4 4000.3174.0001 4000.0000.0001 128

NCIA Server Session with DSPU Example

Figure 169 illustrates an NCIA server session with RSRB/DLSw+ and DSPU.


Figure 169:
NCIA Server Session with RSRB/DLSw+ and DSPU


The following is a configuration file for the network example shown in Figure 169:

ncia server 1 10.2.20.4 4000.3745.0001 4000.0000.0001 128
!
dspu ncia 1
dspu ncia enable-pu lsap 8
!
dspu host HOST-9370 xid-snd 11100001 rmac 4000.1060.1000 rsap 4 lsap 4
!
dspu pu CISCOPU-A xid-rcv 01700001
dspu lu 2 6 host HOST-9370 2
!
interface TokenRing 0
  ring-speed 16
  llc2 xid-retry-time 0
  dspu enable-host lsap 4
  dspu start HOST-9370

NCIA Server Session with RSRB Example

Figure 169 illustrates the use of RSRB with an NCIA server session.


Figure 170:
NCIA Server Session with RSRB


The following is a configuration file for router Cisco 2 for the network example shown in Figure 169:

source-bridge ring-group 44
source-bridge ring-group 22
source-bridge remote-peer 22 tcp 10.2.20.3
source-bridge remote-peer 22 tcp 10.2.20.4
dlsw local-peer
ncia server 1 10.2.20.4 4000.3174.0001 4000.0000.0001 128
ncia rsrb 22 2 33 4 44 1111.1111.2222


hometocprevnextglossaryfeedbacksearchhelp
Copyright 1989-1998 © Cisco Systems Inc.