Полезная информация

cc/td/doc/product/software/ios120/120newft
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

&&Left&&System Error Messages for 12.0 T

How to Read System Error Messages

Error Messages

&&Left&&System Error Messages for 12.0 T

This chapter lists and describes the system error messages for Cisco IOS Release 12.0 T, up to and including 12.0(2)T. The system software sends these error messages to the console (and, optionally, to a logging server on another system) during operation. Not all system error messages indicate problems with your system; some are purely informational, while others may help diagnose problems with communications lines, internal hardware, or the system software.

This chapter only lists error messages for Cisco IOS Release 12.0 T that are not documented in the Cisco IOS Release 12.0 Cisco IOS Software System Error Messages manual. For additional system error messages, refer to the Cisco IOS Software System Error Messages manual.

How to Read System Error Messages

The messages are organized according to the particular system facility that produces the messages. The facility sections appear in alphabetical order, and within each facility section, messages are listed alphabetically by mnemonic. Each error message is followed by an explanation and a recommended action.

System error messages begin with a percent sign (%) and are structured as follows:

%FACILITY-SEVERITY-MNEMONIC: Message-text
 

FACILITY is a code consisting of two or more uppercase letters that indicates the facility to which the message refers. A facility can be a hardware device, a protocol, or a module of the system software. Table 1 lists the system facilities codes.

SEVERITY is a single-digit code from 0 to 7 that reflects the severity of the condition. The lower the number, the more serious the situation. Table 2 lists the severity levels.

MNEMONIC is a code that uniquely identifies the error message.

Message-text is a text string describing the condition. This portion of the message sometimes contains detailed information about the event, including terminal port numbers, network addresses, or addresses that correspond to locations in the system memory address space. Because the information in these variable fields changes from message to message, it is represented here by short strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec]. Table 3 lists the representations of variable fields and the type of information in them.

The following is a sample system error message:

%LINK-2-BADVCALL: Interface [chars], undefined entry point
 

Some error messages also indicate the card and slot reporting the error. These error messages begin with a percent sign (%) and are structured as follows:

%CARD-SEVERITY-MSG:SLOT %FACILITY-SEVERITY-MNEMONIC: Message-text
 

CARD is a code that describes the type of card reporting the error. VIP and FEIP are possible card types.

MSG is a mnemonic that indicates this is a message. It is always shown as MSG.

SLOT indicates the slot number of the card reporting the error. It is shown as SLOT followed by a numeral. (For example, SLOT5.)


Note The prepended portion of the error message (%CARD-SEVERITY-MSG:SLOT) is not shown in the error message listings in this manual.


Table 1: Facility Codes
Code Facility

AAA

TACACS+ authentication, authorization, and accounting security

ADJ

Adjacency subsystem

AIP

ATM Interface Processor

ALIGN

Memory optimization in Reduced Instruction-Set Computer (RISC) processor

ALPS

Airline Protocol Support

AMDP2

AMDP2 Ethernet and Fast Ethernet

APPN

Advanced Peer-to-Peer Networking

ARAP

Apple Remote Access Protocol

ASPP

Asynchronous Security Protocol

AT

AppleTalk

ATM

Asynchronous Transfer Mode

ATMCES

ATM access concentrator PCI port adapter driver

ATMCORE

ATM core

ATMPA

ATM port adapter

ATMSIG

ATM signaling subsystem

ATMSSCOP

ATM Service Specific Connection Oriented Protocol (SSCOP)

AUTORP

PIMv2 AUTORP

BAP

PPP Bandwidth Allocation Protocol (BAP)

BGP

Border Gateway Protocol

BRI

Integrated Services Digital Network (ISDN) Basic Rate Interface

BRIMUX

AS5200 BRIMUX board

BSC

Binary Synchronous Communications mode

BSTUN

Block serial tunneling

C1400

Cisco 1400 platform

C1600

Cisco 1600 platform

C1700

Cisco 1700 platform

C2KATM

Catalyst 2820 ATM module

C3600

Cisco 3600 platform

C542

Voice driver for modular access routers

C5RSP

Cisco Catalyst 5000 platform

C7200

Cisco 7200 platform

CAIM

Compression Advanced Interface Module

CALL_MGMT

Call management subsystem

CALLRECORD

Modem Call Record

CBUS

ciscoBus controller

CDM

Cable Data Modem subsystem

CI

Cisco 7500 platform chassis interface

CIPDUMP

CIP core dump

CIRRUS

CD2430 asynchronous controller

CIRRUS_PM

Slow speed asynchronous/synchronous port module

CLEAR

Clear facility

CLNS

OSI Connectionless Network Service

CLS

Cisco Link Services

CLSDR

Cisco Link Services Driver

CM622

ATM line card driver

CMCC

Cisco Mainframe Channel Connection interfaces

COMP

Point-to-point compression

CONTROLLER

Controller

CPAD

Compression service adapter

CPM

Combo Port Module device driver

CRYPTO

Encryption

CSC2

CSC2/CSC3 CPU cards

CSM

Call switching module

CT3

Channelized T3 port adapter

DBCONN

Database Connection

DBUS

Data bus

DCU

ATM access concentrator PCI port adapter

DEC21140

DEC21140 Fast Ethernet controller

DHCPD

DHCP Server

DIALER

Dial-on-demand routing

DIALSHELF

Dial shelf messages

DLC

Data-link control

DLSw

Data-link switching

DMA

Direct memory access

DNET

DECnet

DRIP

Duplicate RIng Protocol

DRP

Director Response Protocol

DRVGRP

Interface driver

DSCCLOCK

Dial shelf controller clock

DSC_ENV

Cisco AS5800 environment monitor

DSCEXTCLOCK

Dial shelf controller clock

DSI

Cisco AS5800 dial shelf interconnect board

DSPU

Downstream physical unit

DS_TDM

Dial Shelf Time Division Multiplex

DSX0

CT1 RBS timeslot status

DSX1

Channelized E1 (Europe) and T1(US) telephony standard

DUAL

Enhanced Interior Gateway Routing Protocol

DVMRP

Distance Vector Multicast Routing Protocol

EGP

Exterior Gateway Protocol

ENT_API

Entity MIB API

ENV

Environmental monitor card

ENV_MON

Cisco 12000 environmental monitor

EPAD

Encryption port adapter driver

ESWITCH

Ethernet switch port adapter

ETHERNET

Ethernet for the C1000 series

EXPRESSION

Expression MIB

FB

Cisco AS5800 feature board

FBINFO

Cisco 5800 feature board crash information subsystem

FDDI

Fiber Distributed Data Interface

FILESYS

File system

FLASH

Flash nonvolatile memory

FPGA

LS1010 chip-specific

FR

Frame Relay

FR_ELMI

Frame Relay enhanced Local Management Interface

FR_LMI

Frame Relay Local Management Interface

FTC_TRUNK

Cisco 3801 platform

FTPSERVER

FTP server processes

FW

Inspection subsystem

GRIP

Xerox Network Systems (XNS) Routing Protocol

GRP

Gigabit route processor

GRPPOS

POS route processor

GSR_ENV

Gigabit Switch Router environment monitor

GSRIPC

Gigabit Switch Router IPC service routines

GT64010

GT64010 DMA controller driver

HAWKEYE

Token Ring PCI port adapter

HD

HD64570 serial controller

HMM_ASYNC

Hex modem network module asynchronous driver

HOOD

LAN controller 100VG-AnyLAN interface

HP100VG

100VG-AnyLAN PA driver

HUB

Cisco Ethernet hub

IBM2692

IBM Token Ring chipset

IDTATM25

IDT ATM25 network module

IFS

IOS File System

IGRP

Interior Gateway Routing Protocol

ILACC

ILACC driver

INTERFACE_API

Binary API for the interface descriptor block

IP

Internet Protocol

IPACCESS

IP security

IPC

Interprocess communication

IPCGRP

RP interprocess communication

IPCLC

Gigabit Switch Router line card interprocess communication

IPC_RPM

Interprocess communication

IPC_RSP_CBUS

Interprocess communication

IPFAST

IP fast switching

IPFLOW

IP flow

IPMCAST

Gigabit Switch Router line card IP multicast

IPMOBILE

IP Mobility

IPRT

Internet Protocol routing

IP-SNMP

Simple Network Management Protocol specific to IP

IPX

Internetwork Packet Exchange protocol

ISDN

Integrated Services Digital Network

LANCE

Local Area Network Controller Ethernet

LANE

LAN Emulation

LANMGR

IBM LAN Network Manager

LAPB

X.25 Link Access Procedure, Balanced

LAT

DEC local-area transport

LCCEF

ATM Cisco Express Forwarding (CEF) adjacency

LES_FDDI

LAN Emulation Server/Fiber Distributed Data Interface

LEX

LAN extension

LINEPROTO

Line Protocol

LINK

Data link

LLC2

Logical link control type 2

LLIST

Linked list facility

LNMC

LAN network manager

LPD

Line printer daemon

M32X

M32X Basic Rate Interface trunk card

MAILBOX

ChipCom mailbox support

MBRI

Multi-BRI port module

MBUS

Maintenance bus

MBUS_SYS

MBUS system

MCI

Multiport Communications Interface

MICA

Modem ISDN Channel Aggregation modem

MIF68840

PCI MC68840 FDDI port adapter

MIMIC

MCOM integrated modem network modules

MK5

MK5025 serial controller

MMODEM

Integrated modem network module

MODEM

Router shelf modem management

MODEM_HIST

Router shelf modem history/tracing

MODEM_NV

Modem NVRAM

MPA68360

VIP Multi-channel Port Adapter

MROUTE

Multicast route

MUESLIX

Mx serial application-specific integrated circuit (ASIC)

NETWORK_CLOCK

Network clock synchronization

NHRP

Next Hop Resolution Protocol

NIC100

NIC100 driver

NIM

Network interface module

OIR

Online insertion and removal

OOBP

Out of band port

OSPF

Open Shortest Path First

PA

Port adapter

PAD

X.25 packet assembler/disassembler

PARSER

Parser

PERUSER

PPP per-user configuration

PIM

Protocol-independent multicast

PNNI

Private Network-Network Interface

POSDW

Packet over SONET double wide PCI port adapter driver

PPP

Point-to-Point Protocol

PQUICC

MPC860 quad integrated communications controller

PQUICC_FE

MPC860 quad integrated communications controller

QA

Queue and accumulator

QEM

QEM driver

QLLC

Qualified Logical Link Control

QUICC

MC68360 quad integrated communications controller

QUICC_ASYNC

Asynchronous MC68360 quad integrated communications controller

QUICC_Ethernet

Ethernet MC68360 quad integrated communications controller

QUICC_SERIAL

Serial MC68360 quad integrated communications controller

RADIUS

Remote Access Dial-In User Service (RADIUS) facility

RADIX

Radix facility

RCMD

Remote commands

RIP

IP Routing Information Protocol

RPM_VIRTUAL_PORT

RPM virtual port

RPS

Redundant power supply

RSP

Route Switch Processor

RSRB

Remote source-route bridging

RTT

Round trip time monitor

S4T68360

Four-port synchronous serial adapter based on the 68360 processor

SCHED

Scheduler

SDLC

Synchronous Data Link Control

SDLLC

SDLC/logical link control type 2 (LLC2) translation

SEC

IP security

SERVICE_MODULE

Service module

SGBP

Stack Group Bidding Protocol

SHELF

Router shelf

SLIP

Serial Line Internet Protocol

SLOTDUMP

Slot dump

SMF

Software MAC Filter

SMRP

Simple Multicast Routing Protocol

SNAPSHOT

Snapshot dial-on-demand routing

SNMP

Simple Network Management Protocol

SNMP_MGR

SNMP Proxy

SONET

Synchronous Optical Network

SONETMIB

Synchronous Optical Network Management Information Base

SPARC

3800 SPARC coprocessor subsystem

SSE

Silicon switching engine

STANDBY

Hot Standby Router Protocol (HSRP)

STUN

Serial tunneling

SUBSYS

Software subsystems

SW56

Switch 56K

SWITCH

Switch interface

SYS

Operating system

SYSCTLR

System controller subsystem

SYSLOG_SERVER

Syslog-server file system routines

SYSMGT

System management

TAC

Terminal Access Controller Protocol Access Control System

TAGCON

Tag distribution and control

TBRIDGE

Transparent bridging

TCATM

ATM TAG control

TCP

Transmission Control Protocol

TDM

Time-division multiplexing

TDP

Tag Distribution Protocol

TE_LDPB

Traffic engineering loop prevention

TFIB

Tag Forwarding Information Base

TI1570

PCI/TI1570-based ATM port adapter

TIB

Tag Information Base

TMQ

Inbound terminal port queuing

TN

Telnet

TN3270

TN3270 protocol

TR

Token Ring

TRAFFENG

Traffic engineering

TRUNK

E1/T1 trunk card

TSP_TUNNEL

Tag switch path (TSP) tunnel

TTYDRIVER

Router shelf asynchronous driver

TUN

Tunnel

UBR7200

Cable modem termination system

UCODE

Microcode

UNIX

UNIX

UTIL

Utility

VINES

Banyan VINES

VIP

Versatile Interface Processor

VOICE_FSM

MC3810 voice FSM subsystem

VOICE_RC

MC3810 voice resource subsystem

VPDN

Virtual Private Dialup Networking

VPM

Voice port module

VPN

Virtual Private Dialup Network

X25

X.25

XCPA

Mainframe Channel Port Adapter


Table 2: Error Message Severity Levels
Level Description

0 - emergency

System unusable

1 - alert

Immediate action needed

2 - critical

Critical condition

3 - error

Error condition

4 - warning

Warning condition

5 - notification

Normal, but significant, condition

6 - informational

Informational message only

7 - debugging

Appears during debugging only

Error message severity levels correspond to the keywords assigned by the logging global configuration commands that define where and at what level these messages appear. The default is to log messages to the console at the debugging level (7). For more information, see the system configuration chapter and descriptions of the logging command in the appropriate Cisco IOS configuration guide and command reference publications.


Table 3: Representation of Variable Fields in Error Messages
Representation Type of Information

[atalk_address]

AppleTalk address

[atalk_net]

AppleTalk network, either 600 or 600-601

[char]

Single character

[chars]

Character string

[dec]

Decimal number

[enet]

Ethernet address (for example, 0000.FEED.00C0)

[hex]

Hexadecimal number

[inet]

Internet address (for example, 12.128.2.16)

[int]

Integer number

[node]

Address or node name

[sci_notation]

Scientific notation

[t-line]

Terminal line number in octal (or decimal if the decimal-TTY service is enabled)

[v-name]

VINES name; or number (hex or decimal)

Error Messages

This section lists error messages alphabetically by facility and mnemonic.


Error Message   
%ALPS-5-ASCU_DISABLED_ASCU_STUCK: ASCU [hex] on interface [chars] has been disabled since 4 consecutive messages were received from same SID

Explanation   An ALPS ASCU was automatically disabled.

Recommended Action   No action is required.


Error Message   
%ALPS-3-ASCU_FSM_ERR: ASCU [hex] on interface [chars] has an internal FSM error

Explanation   An internal error occurred.

Recommended Action   Turn debug flags on, capture traces, and contact Cisco technical support.


Error Message   
%AUTORP-5-MAPPING: RP for [int]/[dec] is now [int]

Explanation   A new RP has been elected for the subject group prefix.

Recommended Action   No action is required.


Error Message   
%BGP-5-VERSION_WRAP: bgp version wraped

Explanation   The BGP table version reached its maximum value and wrapped around.

Recommended Action   This is an informational message only. However, frequent occurrences of this event might indicate high error rates or high packet loss in the network and the cause should be investigated.


Error Message   
%C1400_PCI-3-BADADDR: c1400_little_endian_addr: Attempted conversion of invalid address (0x[hex])

Explanation   A software error occurred while the PCI device addressing was being determined.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%C1400_PCI-3-BADADDR2: c1400_big_endian_addr: Attempted conversion of invalid address (0x[hex])

Explanation   A software error occurred while the PCI device addressing was being determined.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%C1400_PCI-3-BADPCIRD: PCI Configuration Read Cycle Failed for bus [dec], Device [dec], function [dec], register [dec]

Explanation   A PCI Bus Configuration Read failed. The mainboard needs to be replaced.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%C1400_PCI-3-BADPCIWR: PCI Configuration Write Failed for bus [dec], Device [dec], function [dec], register [dec]

Explanation   A PCI Bus Configuration Write failed. The mainboard needs to be replaced.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%C1400_PCI-3-BIG_ENDIAN_ADDR: qspan_little_endian_addr: Address (0x[hex]) operation is not supported

Explanation   Converting an address to the equivalent address in big endian spance is not supported by the QSpan PCI device. This is most likely a software error.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%C1400_PCI-3-LITTLE_ENDIAN_ADDR: qspan_little_endian_addr: Address (0x[hex]) operation is not supported

Explanation   Converting an address to the equivalent address in little endian spance is not supported by the QSpan PCI device. This is most likely a software error.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%C1400_PCI-3-PCI_NOT_EXIST: PCI Bus bridge does not exist

Explanation   The PCI bus bridge does not exist. The mainboard needs to be replaced.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%C1700-3-BADPA: Invalid Port Adapter type ([dec]) reported for mainboard

Explanation   The "virtual" port adapter type derived from the mainboard type is not one of the supported types. It may be that this mainboard is a new mainboard type and the software release you are running does not support the new mainboard type.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%C1700-1-OVERTEMP: System detected OVERTEMPERATURE condition.
Putting the system in Power save mode and going to rommon.
Please resolve cooling problem and restart system!

Explanation   The environmental monitor detected a high-temperature condition.

Recommended Action   Make sure that the room temperature is not too high and that airflow to the card is not blocked. If this condition persists, the environmental monitor might shut down the system. Call your technical support representative for assistance, if necessary.


Error Message   
%C5RSP-3-RSM_NMP_BRIDGE_INVALID: NMP returned invalid bridge id [dec] for [dec]

Explanation   NMP returned an invalid bridge ID to the RSM.

Recommended Action   Make sure that the TR-BRF VLAN on the RSM is configured on the NMP.


Error Message   
%C5RSP-3-RSM_NMP_CONFIG_MISMATCH: RSM NMP mismatch in config for [dec], RSM [dec], NMP [dec]

Explanation   There is a mismatch in the configuration for this VLAN on NMP and RSM.

Recommended Action   Make sure that the parameters for this VLAN are the same on NMP and on RSM.


Error Message   
%CAIM-1-ELMERREV: AIM in slot [int] not supported by this HW revision

Explanation   The revision level of the Cisco 2600 "Elmer" PLD does not support Compression AIM. The PLD needs to be reprogrammed.

Recommended Action   The Cisco 2600 "Elmer" PLD needs to be reprogrammed to a later revision. Refer to the Release Notes for the Cisco 2600 and Compression AIM on CCO for an explanation of how to reprogram the PLD.


Error Message   
%CAIM-1-HIFNERR: Caim [int]: Hifn 9711 Errors reported: 9711 Status 0x[hex]

Explanation   The specified CAIM reported an Hifn9711 error.

Recommended Action   This message indicates a serious malfunction of the Compression AIM or of the system bus. The Compression AIM should be replaced.


Error Message   
%CAIM-1-INITFAIL: CAIM [dec]: Initialization failed at [chars]

Explanation   The CAIM device would not reset properly, indicating a Compression AIM hardware failure.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%CAIM-1-INVELMT: Invalid CAIM element: [dec]

Explanation   The CAIM element number specified in the command is invalid.

Recommended Action   CAIM element numbers range from 0 to one less than the number of CAIMs possible in your system. Verify the number of CAIMs present in your system.


Error Message   
%CAIM-1-NODEV: AIM slot [dec]: Could not locate Compression AIM; found PCI vendor id 0x[hex] instead

Explanation   The AIM ID PROM indicates that a Compression AIM is present but the PCI vendor/device ID was not an ID that is expected for a Compression AIM.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%CAIM-1-NOMEMORY: CAIM [dec]: Memory allocation failure; could not allocate [chars]

Explanation   An attempt to allocate memory for the specified Compression AIM failed. More RAM may be required to execute this image.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%CAIM-1-NOSUCH: No such CAIM element: [dec]

Explanation   The CAIM element number specified is not present in the system.

Recommended Action   CAIM element numbers range from 0 to one less than the number of CAIMs present in your system. Verify the number and presence of CAIMs in your system.


Error Message   
%CAIM-1-PCIABT: Caim [int]: PCI Abort reported: status 0x[hex]

Explanation   The specified CAIM reported a bus error (PCI Abort).

Recommended Action   This message could indicate a serious malfunction of the Compression AIM or of the system bus, and the Compression AIM should be replaced. A second possible explanation is that there is a mismatch in the configured compression algorithm on either side of a serial link. This situation can also give rise to PCI Abort problems. The recommended action in this case is to configure matching compression algorithms on either side of the link and then to reboot the router that experienced the PCI Abort.


Error Message   
%CAIM-6-SHUTDOWN: [chars] shutting down

Explanation   The specified CAIM shut down or may have been physically removed. This message also occurs when the clear aim command is used.

Recommended Action   This is an informational message only. It occurs in normal operation.


Error Message   
%CAIM-6-STARTUP: [chars] starting up

Explanation   The specified CAIM has initialized successfully.

Recommended Action   This is an informational message only. It occurs in normal operation.


Error Message   
%CAIM-1-UNEXPINT: Unexpected AIM Interrupt

Explanation   An AIM interrupt was received from an unknown AIM device. No recognizable AIM is installed in the system, and yet an AIM interrupt was received.

Recommended Action   If a Compression AIM is installed in the Cisco 2600, then it is defective and must be replaced. If another AIM is installed in the Cisco 2600, then it must be removed. If no AIM is installed, then the Cisco 2600 unit is defective and must be replaced.


Error Message   
%CALLRECORD-3-MCOM_TERSE_CALL_FAILED_REC: [chars]

Explanation   Terse Mica Call Failed Record

Recommended Action   No action is required.


Error Message   
%CALLRECORD-3-MCOM_TERSE_CALL_REC: [chars]

Explanation   Terse Mica Call Record

Recommended Action   No action is required.


Error Message   
%CALLRECORD-3-MICA_TERSE_CALL_FAILED_REC: [chars]

Explanation   Terse Mica Call Failed Record

Recommended Action   No action is required.


Error Message   
%CALLRECORD-3-MICA_TERSE_CALL_REC: [chars]

Explanation   Terse Mica Call Record

Recommended Action   No action is required.


Error Message   
%COMP-3-COMPERR: [chars]: COMPRESS: (stac error!) status: [dec], size in: [dec], size out: [dec]

Explanation   An internal software error occurred.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%CRYPTO-6-CERTFAIL: Certificate enrollment failed

Explanation   The certificate enrollment encountered a fatal error.

Recommended Action   Contact the CA administrator.


Error Message   
%CRYPTO-6-CERT_FATAL_ERR: [chars]

Explanation   The certificate enrollment encountered a fatal error.

Recommended Action   Contact the CA administrator.


Error Message   
%DBUS-3-MSGOVERFLOW: Slot [dec], too many DBUS messages

Explanation   A board in the indicated slot tried to send too many logger messages.

Recommended Action   Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.


Error Message   
%DHCPD-4-DECLINE_CONFLICT: DHCP address conflict: client [chars] declined %I

Explanation   The DHCP client detected an address conflict. Another host is using the specified IP address. After resolving the conflict, issue the clear ip dhcp conflict command.

Recommended Action   Resolve the misconfiguration. Clear the conflict from the DHCP database.


Error Message   
%DHCPD-2-MALLOC_ERROR: There is inadequate memory for DHCP services

Explanation   DHCP could not allocate mandatory data structures.

Recommended Action   Add memory.


Error Message   
%DHCPD-2-NO_PROCESS: DHCP could not start its [chars] process

Explanation   DHCP could not start one of its processes.

Recommended Action   Add memory.


Error Message   
%DHCPD-4-PING_CONFLICT: DHCP address conflict: server pinged %I

Explanation   The DHCP server detected an address conflict. Another host is using the specified IP address. After resolving the conflict, issue the clear ip dhcp conflict command.

Recommended Action   Resolve the misconfiguration. Clear the conflict from the DHCP database.


Error Message   
%DHCPD-2-READ_DEADLOCK: DHCP has detected a deadlock condition (excessive read failures)

Explanation   The DHCP server could not read bindings from any database agent. All read attempts failed. To prevent a possible deadlock, the server made all pool addresses available for assignment.

Recommended Action   Verify that all URLs are correct and connectivity exists between the server and all database agents. Check for corrupt database files. All files must contain the , , keywords. Issue the show ip dhcp database command. If there are aborted file transfers, increase the appropriate timeouts. Restart the DHCP server.


Error Message   
%DHCPD-3-READ_ERROR: DHCP could not read bindings from [chars]

Explanation   The DHCP server could not read bindings from the specified database agent.

Recommended Action   Verify that the URL is correct and connectivity exists between the server and database agent. Check for a corrupt database file. The file must contain the , , keywords. Issue the show ip dhcp database command. If there are aborted file transfers, increase the database transfer timeout.


Error Message   
%DHCPD-2-RECVMSG_ERROR: Recvmsg failed unexpectedly. DHCP services have been terminated

Explanation   The reason for failure is unknown.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DHCPD-4-RELAY_ONLY: DHCP will run as a relay agent only

Explanation   DHCP could not start its database process. The server component has been disabled. Only the relay agent is active.

Recommended Action   Add memory.


Error Message   
%DHCPD-2-SOCKET_ERROR: DHCP could not open UDP port [int]

Explanation   DHCP could not open UDP port 67 (bootps).

Recommended Action   Check if another application is using UDP port 67. If the port is available, add memory.


Error Message   
%DHCPD-3-WRITE_ERROR: DHCP could not write bindings to [chars]

Explanation   The DHCP server could not write bindings to the specified database agent.

Recommended Action   Verify that the URL is correct and connectivity exists between the server and database agent. Issue the show ip dhcp database command. If there are aborted file transfers, increase the database transfer timeout.


Error Message   
%DS_TDM-3-ASSERT_FAIL: Slot [dec] Assertion failed: file `[chars]', line [dec]

Explanation   An internal sanity check failed.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-BAD_CONN: Slot [dec] Unrecognized TDM connect message received ([dec]) on [chars] feature board

Explanation   An unrecognized TDM connect message was received.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-BAD_DISCONN: Slot [dec] Unrecognized TDM disconnect message received ([dec]) on [chars] feature board

Explanation   An unrecognized TDM disconnect message was received.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-BAD_DSIP: Slot [dec] Unrecognized DSIP message received ([dec]) on [chars] feature board

Explanation   An unrecognized DSIP message was received.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-CONV_CLOSE: Slot [dec] Open MT8986 (addr: 0x[hex]) connection failed - STo[dec], CHo[dec]

Explanation   An attempt to disable a rate converted connection failed.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-CONV_OPEN: Slot [dec] Open MT8986 (addr: 0x[hex]) [chars] connection failed - STi[dec], CHi[dec], STo[dec], CHo[dec]

Explanation   An attempt to establish a rate converted connection failed.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-TDM_CLOSE: Slot [dec] Close MT90820 (addr: 0x[hex]) connection failed - STo[dec], CHo[dec]

Explanation   An attempt to disable a digitally switched connection failed.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-TDM_OPEN: Slot [dec] Open MT90820 (addr: 0x[hex]) connection failed - STi[dec], CHi[dec], STo[dec], CHo[dec]

Explanation   An attempt to establish a digitally switched connection failed.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-VERIFY_DISCONN: Slot [dec] [chars] failed to verify disconnect: sto = [dec], ch_out = [dec]

Explanation   An attempt to verify a TDM hardware component failed.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-VERIFY_HILOWMEM: Slot [dec] [chars] failed to verify himem, or lowmem: sto = [dec], ch_out = [dec], sti = [dec], ch_in = [dec]

Explanation   An attempt to verify a TDM hardware component failed.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DS_TDM-3-VERIFY_IMS: Slot [dec] [chars] failed to verify IMS: 0x[hex]

Explanation   An attempt to verify a TDM hardware component failed.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%DVMRP-4-REJDEFROUTE: Rejecting default route from [int]

Explanation   Two routers on each side of a tunnel sent default routes to each other.

Recommended Action   Correct the router configuration.


Error Message   
%HMM_ASYNC-3-HMM_HARDWARE_EXCEPTION: HMM: Digital Modem Card [dec] hardware exception : [chars]

Explanation   This error may be an intermittent or permanent hardware failure.

Recommended Action   Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.


Error Message   
%HMM_ASYNC-3-MODEM_MAILBOX_IS_FULL: HMM Modem [dec]/[dec] Mailbox is Full, command [hex] not sent

Explanation   An error occurred while commands were delivered to the modem module. This error may be a transient failure. This message repeating every 30 seconds may indicate a failed modem module.

Recommended Action   If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.


Error Message   
%IPC_RPM-3-CARDERR: [chars]

Explanation   The IPC card twice registered itself to the IPC master.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%IPC_RPM-3-INVMSG: [chars] ([dec])

Explanation   An invalid IPC message was received during cc command execution.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%IPC_RPM-3-INVNUM: [chars] ([dec])

Explanation   The IPC application tried to send a message that was larger than IPC could handle. The message was not transmitted.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%IPC_RPM-3-NOBUF: [chars]

Explanation   The IPC ran out of memory buffers.

Recommended Action   Reduce the number of applications currently running on the IPC. Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%IPC_RPM-3-SEATERR: [chars] [chars]

Explanation   The ID associated with an IPC card is either missing or duplicated, or cannot be created.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%IPMOBILE-2-ASSERTFAILED: IPMOBILE assertion failed: [chars]

Explanation   The software detected an inconsistency. This error is considered serious. The router will attempt to continue, but IP Mobility processing may be impaired.

Recommended Action   Copy the error message exactly as it appears. Note any IP Mobility problems that you are experiencing, and report the error to your technical support representative.


Error Message   
%IPMOBILE-3-NOSOCKET: Unable to open socket

Explanation   The requested operation could not be accomplished because of a low memory condition.

Recommended Action   Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.


Error Message   
%IPMOBILE-6-SECURE: Security violation on [chars] from [chars] [int] - errcode [chars] ([dec]), reason [chars] ([dec])

Explanation   A security violation occurred during a registration attempt.

Recommended Action   This is an informational message only. No action is required.


Error Message   
%ISDN-6-SETUP_PENDING: Interface [chars] SETUP collision on Channel [dec], accepting received SETUP

Explanation   A SETUP was received that collided with a pending SETUP.

Recommended Action   This is an informational message only. No action is required.


Error Message   
%LSS-4-LSIPC: [chars] [dec], LSS_COMPLAIN_IVL

Explanation   LSIPC warning---LSIPC is timing out. Microcode on that interface may not be responding.

Recommended Action   E-PAM may not be responding.


Error Message   
%MICA-3-WRONGMODULE: Module in socket [dec] (board-id=[dec]) is [chars] module; card is not [chars] card

Explanation   The modem module in the indicated socket is inappropriate for the modem card it is on.

Recommended Action   Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.


Error Message   
%POSDW-3-UNSUPPORTED: [chars]

Explanation   This platform does not support POSDW hardware.

Recommended Action   Upgrade your system.


Error Message   
%PQUICC_FE-4-BABBLE: PQUICC/FE([dec]/[dec]), Babble error

Explanation   The transmitter has been on the channel longer than the time taken to transmit the largest frame.

Recommended Action   The system should recover. No action is required.


Error Message   
%PQUICC_FE-5-COLL: PQUICC/FE([dec]/[dec]), Excessive collisions, TDR=[dec], TRC=[dec]., MSGDEF_LIMIT_SLOW

Explanation   Ethernet/Fast Ethernet is seeing multiple collisions. This error may occur under heavy loads.

Recommended Action   The system should recover. No action is required.


Error Message   
%PQUICC_FE-1-INITFAIL: PQUICC/FE([dec]/[dec]), Init failed, CSR[dec]=0x[hex]

Explanation   The software failed to initialize/restart an Ethernet/Fast Ethernet interface.

Recommended Action   Clear the interface. If the message recurs, call your technical support representative for assistance.


Error Message   
%PQUICC_FE-1-INITFAILP: PQUICC/FE([dec]/[dec]), Init failed, CSR[dec]=0x[hex]

Explanation   The FEC could not allocate an I/O buffer pool.

Recommended Action   Clear the interface. If the message recurs, call your technical support representative for assistance.


Error Message   
%PQUICC_FE-5-LATECOLL: PQUICC/FE([dec]/[dec]), Late collision

Explanation   Late collisions occurred on the Ethernet/Fast Ethernet interface.

Recommended Action   If the interface is Fast Ethernet, verify that both peers are in the same duplex mode. For regular Ethernet, the system should recover. No action is required.


Error Message   
%PQUICC_FE-5-LOSTCARR: PQUICC/FE([dec]/[dec]), Lost carrier. Transceiver problem?

Explanation   The cable and/or transceiver is not connected.

Recommended Action   Connect the cable and/or transceiver.


Error Message   
%PQUICC_FE-1-MEMERR: PQUICC/FE([dec]/[dec]), Memory error, CSR[dec]=0x[hex]

Explanation   The interface could not access system resources for a long time. This problem may occur under very heavy loads.

Recommended Action   The system should recover. No action is required. If the message recurs, call your technical support representative for assistance.


Error Message   
%PQUICC_FE-2-NOISL: Interface [chars] does not support ISL

Explanation   The interface cannot be configured as an ISL trunk.

Recommended Action   Check the router configuration.


Error Message   
%PQUICC_FE-3-OVERFLO: PQUICC/FE([dec]/[dec]), Receive overflow

Explanation   While receiving a frame, the controller chip's local buffer transmitted insufficient data because data could not be transferred to DRAM fast enough to keep pace with its input rate. Normally, such a problem is temporary, depending on transient peak loads within the system.

Recommended Action   The system should recover. No action is required.


Error Message   
%PQUICC_FE-3-OWNERR: PQUICC/FE([dec]/[dec]), Buffer ownership error, pak=0x[hex]

Explanation   The software detected an error in descriptor ownership.

Recommended Action   Try a later version of the software. If the message recurs, call your technical support representative for assistance.


Error Message   
%PQUICC_FE-1-SHOWFAIL: PQUICC/FE([dec]/[dec]), Memory error, CSR[dec]=0x[hex]

Explanation   The FEC could not allocate memory to the display controller.

Recommended Action   Clear the interface. If the message recurs, call your technical support representative for assistance.


Error Message   
%PQUICC_FE-3-UNDERFLO: PQUICC/FE([dec]/[dec]), Transmit underflow

Explanation   While transmitting a frame, the controller chip's local buffer received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally, such a problem is temporary, depending on transient peak loads within the system.

Recommended Action   The system should recover. No action is required.


Error Message   
%RADIUS-3-PICKERR: Internal pick-server error: [chars]

Explanation   RADIUS encountered an internal consistency error.

Recommended Action   Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.


Error Message   
%RPM-4-COOKIE: Corrupt or missing MAC address cookie
using random base [sci_notation]

Explanation   The contents of MAC address EEPROM are invalid. The system is providing random MAC addresses.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM-4-NOCPUVER: Invalid CPU ID, assuming revision 1

Explanation   The CPU ID could not be read from the EEPROM. This error is probably caused by a hardware failure.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM-3-NOMAC: Can't allocate MAC address for interface [int]/[int]

Explanation   MAC address allocation failed because of an incorrect slot and port combination, which exceeds the maximum available hardware.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM-4-PCIVALID: PCI activation failed, bay [dec], 0x[hex]

Explanation   The system received an invalid PCI signal from the port adapter. This error is probably caused by a hardware failure.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM_VIRTUAL_PORT-3-CONNDEL: [chars]

Explanation   The delete request to PXM has failed, timed out, or been rejected by PXM.

Recommended Action   In the case of failure or timeout, the connection's state will be set to TIMEOUT and the resync process will periodically attempt to update PXM. In the case where the request is rejected by PXM (which should never occur), copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM_VIRTUAL_PORT-3-CONNUPDATE: [chars]

Explanation   The reconfiguration request to PXM has failed, timed out, or been rejected by PXM.

Recommended Action   In the case of failure or timeout, the connection's state will be set to TIMEOUT and the resync process will periodically attempt to update PXM. In the case where the request is rejected by PXM, the connection state will be set to FAILED until the connection is deleted or reconfigured.


Error Message   
%RPM_VIRTUAL_PORT-3-IPCERR: [chars] Error String = [chars]. Error Code = [dec]

Explanation   The RPC/IPC request to PXM has failed or been rejected by PXM.

Recommended Action   If the error message indicates rpc-timeout, the last command must be retried later. For other error cases, copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM_VIRTUAL_PORT-3-IPCPAK: [chars] Message size = [dec]

Explanation   The ipc_get_pak_message failed. This error could be caused by insufficient memory.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM_VIRTUAL_PORT-3-IPCSIZE: [chars] Message size = [dec]

Explanation   The size of the message that was supposed to be sent to PXM (or was received from PXM) is too big.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM_VIRTUAL_PORT-3-RPCREQERR: [chars] request_type = [dec]

Explanation   The rpc request from Virtual-Port or Resync process is not valid. This error should never occur.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%RPM_VIRTUAL_PORT-3-VRTLERR: An unexpected FW error has occurred. [chars]

Explanation   An unexpected firmware error has occurred.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%SYS-3-BAD_RESET: Questionable reset of process [dec] on tty[t-line]

Explanation   A process was reset without giving it a chance to fix itself.

Recommended Action   Copy the error message exactly as it appears, and report it to your technical support representative.


Error Message   
%TBRIDGE-4-VCPAKDROP: Subscriber SA [sci_notation] moved or loop between circuits [dec] and [dec]

Explanation   A subscriber bridged packet dropped because of a potential circuit loop or a roaming host at the subscriber end of the network.

Recommended Action   Clear the bridge table. If the problem persists, it is not a roaming host, but a loop between virtual circuits at the subscriber end of the network. Take looping virtual circuits out of service and/or shut the software interface they are on while the subscriber is contacted to remove the loop condition at the subscriber end of the network.


Error Message   
%VIP-3-AFOVERFLOW: VIP address filter table full

Explanation   The VIP Ethernet-like interface uses an internal MAC address table to filter incoming packets. Once the table is full, additional address entries are rejected. Any incoming packet with a destination address not in the table will be ignored.

Recommended Action   The address table is consumed by various protocols, such as PIM or HSRP. If too many HSRP entries are configured for one interface, the entry could be exhausted. Distribute some of those HSRP entries to another Ethernet interface.


Error Message   
%VPDN-4-REFUSED: Session for [chars] Refused status = [hex]

Explanation   The remote server refused this session.

Recommended Action   Check the configuration on the HG or LNS.


hometocprevnextglossaryfeedbacksearchhelp

Copyright 1989-1999©Cisco Systems Inc.